Welch Allyn IMAGETEAM 3800 User's Guide Page 67
- Page / 174
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
6-3
Non Decoded Laser Emulation Idle
The idle describes the state of the scanner when no data is being transmitted.
When in Non Decoded mode, you must set the scanner’s idle state to match the
idle state for the device to which the scanner is connected.
Default=High.
Disabling the Secondary Interface
You can temporarily disable the secondary interface, but still retain the
secondary interface settings in the scanner’s memory by scanning the Disable
bar code below. To re-enable the secondary interface, scan the Enable bar
code.
Default=Disable
.
Secondary Trigger Mode
Manual Trigger:
You must press the scanner trigger to scan. When not
scanning, idle power is maintained.
Default=Manual Trigger
.
Low
*High
* Disable
Enable
* Manual Trigger
- Hand Held Linear Imager 1
- Canadian Notice 3
- UL and cUL Statement 4
- LED Safety Statement 4
- TÜV Statement 4
- C-TIC Statement 4
- Table of Contents 5
- Chapter 3 - Output 6
- Chapter 4 - Data Editing 6
- Chapter 5 - Data Formatting 7
- Chapter 7 - Symbologies 7
- Chapter 8 - Cloning 10
- Chapter 9 - Visual Menu 10
- Chapter 10 - Interface Keys 10
- Chapter 11 - Utilities 10
- Chapter 12 - Default Charts 11
- Chapter 15 - Maintenance 12
- Chapter 16 - Customer Support 12
- About This Manual 13
- Unpacking the Scanner 14
- IT3800 Scanner Identification 15
- IT3900 Scanner Identification 15
- (Keyboard Wedge) 16
- Plug and Play 18
- 11 and 3800LR-15 modelsonly 21
- (Default for -11 Models) 21
- Default=USBKeyboard (PC) 22
- USB Converter 23
- OCIA Interface 24
- Nixdorf OCIA Interface 25
- Default=P1 26
- Keyboard Wedge Connection 27
- Terminal ID 28
- Supported Terminals 29
- Keyboard Country 30
- Keyboard Style 31
- Keyboard Modifiers 32
- NumericKeypad Mode: 33
- AutomaticDirect Connect: 33
- Serial Port Connection 34
- Default=9600 35
- (continued) 37
- RS-232 Handshaking 38
- Default=Code 39 Format 39
- Default=25inches/second 40
- Default=Black High 40
- Default=Idle 41
- Default=60 41
- Default=50ms 42
- Default=270 s/s 43
- Default=High 43
- Default=Normal 44
- Default=Voting Normal 44
- =Don’t Reduce Quite Zone 44
- Default=Short 45
- Default=NoDelay 46
- Manual/Serial Trigger: 46
- Defaultfor 46
- Serial Trigger Time Out: 46
- Presentation Mode: 48
- Prefix/Suffix Overview 49
- To Add a Prefix or Suffix: 50
- Prefix Selections 52
- Suffix Selections 52
- Symbology Chart 53
- Default=Enable 55
- Prefix Scanned Data Suffix 56
- Interfunction Delay 58
- Intermessage Delay 58
- To Add a Data Format 59
- Other Programming Selections 60
- Data Format Editor Commands 60
- Search Commands 61
- Miscellaneous Commands 61
- Data Format Editor 62
- Default= 63
- Data Formatter On 63
- Secondary RS-232 Connection 65
- Default=36scans/second 66
- Default=WhiteHigh 66
- Default=Disable 67
- Manual Trigger: 67
- Default=Manual Trigger 67
- All Symbologies On 69
- Default=Don’t Transmit 70
- Default = No Check Character 71
- No Check Character 71
- Concatenation 72
- Default= Don’t 74
- Transmit 74
- Code 39, continued 76
- Default = No Check Digit 79
- Interleaved 2 of 5, continued 80
- Code 2 of 5 82
- IATA Code 2 of 5 83
- Matrix 2 of 5 84
- Default=Two Check Digits 85
- Code 11, continued 86
- Code 128, continued 88
- Default=AIM Telepen Output 89
- Telepen, continued 90
- Default=On 100
- Default = Off 100
- Validate and Transmit 104
- Validate,butDon’tTransmit 104
- MSI, continued 105
- Message Length 106
- RSS-14 Limited 107
- RSS-14 Expanded 108
- China Post Code 109
- Default=Off 111
- Procedure 113
- Visual Menu 115
- Upgrading USB Firmware 116
- Interface Keys 117
- Supported Interface Keys 119
- Show Software Revision 123
- Show Data Format 123
- Default Charts 125
- Wand Emulation Selections 126
- Output Selections 126
- Data Editing Selections 127
- Codabar Selections 127
- Code 39 Selections 127
- Interleaved 2 of 5 Selections 128
- Code 93 Selections 128
- Code 2 of 5 Selections 128
- IATA Code 2 of 5 Selections 128
- Matrix 2 of 5 Selections 128
- Code 11 Selections 129
- Code 128 Selections 129
- Telepen Selections 129
- EAN/JAN 13 130
- EAN/JAN 8 130
- MSI Selections 131
- Plessey Selections 131
- RSS-14 Selections 131
- PDF417 Symbology Selections 131
- Menu Command Syntax 133
- Query Commands 134
- Responses 135
- Examples of Query Commands 135
- Trigger Commands 136
- Menu Commands 137
- Selection 138
- Serial Command 138
- PDF417 Wand Emulation 139
- Prefix/Suffix Selections 140
- Data Formatter Selections 140
- Symbologies 141
- Parameter Specification 149
- Standard Cable Pinouts 151
- Standard Cable Pinouts 152
- Serial Output 154
- Scan Maps 156
- 13/15 mil 158
- Caution: 161
- Troubleshooting 162
- Application Support 164
- Product Service Department 165
- E-mail: [email protected] 167
- Limited Warranty 168
- Sample Symbols 170
- Vehicle Registration 171
- 123456-9$ 171
- Programming Chart 172
- 4619 Jordan Road 174
- P.O. Box 187 174
Related products and manuals for Bar code readers Welch Allyn IMAGETEAM 3800
(189 pages)© 2020, manymanuals.com. All rights reserved. | 1.418 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals