Welch Allyn SCANTEAM 5770 LASER Specifications Page 125
- Page / 200
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
5 - 21
Code 11, continued
Code 11 Message Length
The message length selection is used to set the valid reading length of the bar
code. If the data length of the scanned bar code doesn’t match the valid reading
length, the scanner will ignore the symbol and continue scanning. You may wish
to set the same value for minimum and maximum length to force the scanner to
read fixed length bar code data. This helps reduce the chances of a misread.
EXAMPLE: Decode only those bar codes with a count of 9-20 characters.
Min. length = 09 Max. length = 20
EXAMPLE: Decode only those bar codes with a count of 15 characters.
Min. length = 15 Max. length = 15
For a value other than the minimum and maximum message length defaults,
scan the bar codes below, then scan the appropriate value and Save bar codes
on the Programming Chart inside the back cover. Minimum and Maximum
lengths = 1-80. Defaults are Minimum = 4, Maximum = 80.
If you make an error while scanning the digits (before scanning Save), scan
Discard on the back cover, scan the Minimum or Maximum bar code, scan the
correct digits, and Save again.
Minimum
Maximum
- CORDLESS SCANNING SYSTEM 1
- Disclaimer 2
- Canadian Notice 3
- R&TTE Directive 4
- C.S.A. Statement 5
- IT3870 Scanner 6
- Right Side View 6
- ST2070 Base - Bottom 8
- Table of Contents 9
- Work Group Prefix On/Off 4-13 11
- Decode Beep Selection 4-20 12
- Chapter 5 - Symbology Menu 12
- Chapter 9 - Customer Support 15
- Chapter 10 - Default Chart 16
- Introduction and Installation 17
- Cordless Scanner 18
- Cordless Base 18
- Charge Pack Recommendations 19
- Conditioning the Charge Pack 20
- °C (68°F) 20
- Keyboard Wedge Interface 22
- RS-232 Interface 23
- ST5770 Scanner LED Indication 27
- ST2070 Base LED Indication 28
- Association Process 30
- Scanner is Out of Range 31
- Glossary 32
- Acknowledgement from the Base 33
- Acknowledgement from the Host 34
- Base Wall Mount Bracket 37
- Visual Menu 37
- Introduction 39
- <Factory Default> 40
- Black High 42
- White High 42
- Non Decoded Laser Emulation 43
- Terminal Interface Selections 44
- Keyboard Country 46
- Keyboard Style Selections 47
- Keyboard Style Modifiers 48
- Output Delays Selection 49
- Wand Emulation Selections 50
- Output Polarity Selection 51
- Power Settings 52
- Battery Conservation Mode 53
- Timeout Period Selections 54
- Reset Factory Settings 55
- Revision Report 55
- Communications Menu 57
- Host Port Protocol 58
- Default Host Port Protocol 58
- Host Port Communications 61
- Auxiliary Port Input Protocol 67
- Protocol Selection 71
- Data Character Selection 72
- Aux Prefix/Suffix Selections 73
- Example 1: Add a Prefix 74
- Example 2: Add a Suffix 74
- Aux Prefix Selection 76
- Aux Suffix Selection 76
- Aux Prefix On/Off 77
- Aux Suffix On/Off 77
- Default Aux 78
- Data Format setting = none 78
- Other Programming Selections 79
- Aux Format Editor Commands 80
- Aux Data Format Editor 82
- Aux Data Formatter 82
- Require Aux Data Format 83
- Alternate Aux Data Formats 83
- Application Work Group Menu 85
- Output Selections 86
- Remove Scanner Selection 87
- Beeper Volume Selection 87
- Beeper Pitch 88
- Scanner Voting Selection 88
- AIM I.D. Prefix 90
- Code I.D. Prefix 90
- Symbology Chart 91
- To Add a Prefix or Suffix: 93
- Prefix Selections 95
- Suffix Selections 95
- Work Group Prefix On/Off 97
- Send Commands 100
- Move Commands 100
- Search Commands 101
- Miscellaneous Commands 101
- Data Format Editor 102
- Data Formatter 102
- Require Data Format 103
- Alternate Data Formats 104
- Decode Beep Selection 104
- Symbology Menu 105
- Start/Stop Characters 106
- Codabar, continued 107
- A12D D34A 108
- Character 108
- Stop Start StopStart 108
- Concatenation 109
- Code 39 110
- Code 39, continued 111
- Code 93, continued 116
- Interleaved 2 of 5 117
- Interleaved 2 of 5, continued 118
- Code 2 of 5 120
- Code 2 of 5, continued 121
- Matrix 2 of 5 122
- Matrix 2 of 5, continued 123
- Code 11 Check Digits Required 124
- Code 11, continued 125
- Code 128 126
- Code 128, continued 127
- Telepen, continued 130
- China Post Code (IT3870 only) 131
- China Post Code 131
- China Post Code, continued 132
- RSS-14 (IT3870 only) 133
- RSS Limited (IT3870 only) 133
- RSS Expanded (IT3870 only) 133
- RSS Expanded Message Length 134
- PDF417 (IT3870PDF only) 135
- PDF417 (IT3870), continued 136
- Show GLI Blocks 137
- MicroPDF417 (IT3870PDF only) 140
- MicroPDF417 140
- MicroPDF417 Message Length 141
- < Default All EAN 142
- EAN/JAN 8 144
- EAN/JAN 13 145
- , continued 147
- UPC E0 Check Digit 148
- Number System 148
- UPC E0, continued 149
- EAN/UPC Addenda 150
- UPC Addenda 151
- Supported Interface Keys 153
- *** DEC VT 220/320/340/420 156
- Parameter Specification 159
- Radio Specifications 160
- Product Specifications 161
- Specifications 162
- Recommended Storage 163
- Connectors & Pinouts 164
- +9 Volts DC (example) 167
- 3/4 View 169
- Top View 169
- Front View 169
- Side View 169
- Scan Maps - IT3870 171
- Scan Maps - ST5770 174
- SCANTEAM 5770 ALR 177
- Warning: 179
- Replacing the Interface Cable 180
- To Reset Factory Settings 180
- Troubleshooting 181
- Customer Support 183
- Help Desk 185
- Limited Warranty Durations 186
- Default Chart 187
- Auxiliary Port Communications 188
- Prefix/Suffix Selections 189
- Data Formatter Selections 189
- Codabar Selections 189
- Code 128 Selection 191
- Telepen Selection 191
- China Post Code Selection 191
- RSS-14 Selection 191
- PDF417 Selection 191
- •UCC Composite Symbology 192
- UPC E1 Selection 193
- EAN/UPC Addenda Selection 193
- Sample Symbols 196
- Programming Chart 198
- 4619 Jordan Road 200
- P.O. Box 187 200
Related products and manuals for Bar code readers Welch Allyn SCANTEAM 5770 LASER
(12 pages)© 2020, manymanuals.com. All rights reserved. | 0.690 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals